Just How to Remove as Well as Replace a Bath Tub
Just How to Remove as Well as Replace a Bath Tub
Blog Article
What're your thoughts with regards to A Step-by-Step Guide to Installing a Bathtub?
Setting up a bath tub isn't exactly rocket science, but it does require strong plumbing, woodworking, and also sometimes, tiling skills. Replacing an old bath tub with a new one is likewise a moderately hard job. If the old tub is easily obtainable, the task can relocate quickly; if you need to open up a wall to get rid of the old tub and also position the brand-new tub, the job is a lot harder. In either case, the task is within a residence handyman's abilities, although you will certainly require a helper to move out the old tub and set in the new one. Make sure you have actually certified on your own for the work and also fit attempting it. Instead of employing a specialist to take control of a halfway-completed project, it is better to consider employing one prior to you begin. Chances are you might require an expert plumber to make tube connections.
This article will certainly aid you set up a new bathtub in your washroom if you have actually already bought a brand-new bathtub as well as don't require to transform the plan of your previous supply of water pipes.
Your devices and also product checklist should make up the following:
Removing Old Taps
If you need to change old faucets with new ones as a part of your installation, after that the first thing you must do is disconnect the water. After doing so, switch on the taps to drain pipes any type of water continuing to be in the system. The process of getting rid of the existing faucets can be rather problematic as a result of the limited gain access to that is typically the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipes to the faucets. Have a fabric ready for the remaining water that will originate from the pipelines. As soon as the supply pipelines have been removed, make use of the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the single faucets from transforming during this process. Once the faucets have actually been eliminated, the holes in the bath/basin will have to be cleansed of any type of old securing compound.
Prior to carrying on to fit the brand-new taps, contrast the pipe connections on the old faucets to the new taps. If the old taps are longer than the new faucets, then a shank adapter is needed for the new taps to fit.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will require a plastic port to stop damage to the thread. One end of the adapter fits on the plastic tail of the faucet and the other end supplies a connection to the existent supply pipelines.
If you require to fit a monobloc, after that you will need minimizing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, position the faucet in the installing hole in the bath/basin guaranteeing that the washers remain in place between the faucet as well as the sink. Safeguard the tap in position with the manufacturer supplied backnut. Once the faucet is safely in place, the supply pipes can be connected to the tails of the taps. The taps can either be linked by using corrugated copper piping or with typical faucet adapters. The former type must be connected to the faucet finishes initially, tightening only by hand. The supply pipelines can later be connected to the other end. Tighten both ends with a spanner after both ends have been attached.
Mounting the Tub
Utilizing both wood boards under its feet, position the bath tub in the called for position. The wooden boards are handy in equally spreading the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto 4 small factors.
The next objective is to make sure that the bathtub is leveled all round. This can be achieved by inspecting the spirit level as well as adjusting the feet on the bathtub until the level checks out degree.
To mount faucets, fit all-time low of the furthest flexible tap port to the appropriate supply pipeline by making a compression sign up with; then do the exact same for the other tap.
Activate the supply of water and also examine all joints as well as brand-new pipework for leaks as well as tighten them if needed. Load the bathtub and additionally inspect the overflow electrical outlet as well as the regular outlet for leaks.
Lastly, repair the bath paneling as defined in the maker's instruction manual. Tiling and sealing around the bathtub needs to wait till the tub has been utilized at the very least once as this will certainly settle it right into its last setting.
Planning for the Setup
To start with, the supporting structure provided with the bathroom ought to be fitted (if called for) according to the maker's instructions. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is very important to see to it that if the tap comes with a plastic washing machine, it is fitted in between the bath and also the faucets. On a plastic bath, it is additionally practical to fit a sustaining plate under the taps device to prevent stress on the tub.
Fit the adaptable faucet ports to the bottom of both taps making use of 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet with the hole in the bath. Use the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make sure you utilize every one of the provided washing machines.
Connect the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom should now prepare to be fitted in its last position.
Tiling Around the Bathtub
In the location where the bathroom satisfies the floor tile, it is required to secure the accompanies a silicone rubber caulking. This is very important as the installation can relocate sufficient to crack an inflexible seal, causing the water to pass through the wall in between the bath as well as the tiling, resulting in issues with dampness and also possible leakages to the ceiling below.
You can choose from a variety of coloured sealants to assimilate your components and fittings. They are offered in tubes and also cartridges, as well as are capable of securing voids up to a size of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always load the bath tub with water prior to sealing, to enable the activity experienced when the tub is in usage. The sealer can fracture fairly very early if you do not take into consideration this motion before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise quickly readily available on the market. It is suggested to fit the ceramic tiles utilizing water-resistant or water resistant sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-01-b02d6683a8ee4621bf9b9ac7ab0b1dd2.jpg)
I have been very serious about Tools You Need to Install a New Bathtub and I hope you enjoyed our page. So long as you enjoyed reading our blog post kindly don't forget to share it. I praise you for your time. Visit again soon.
Book A Service Call
Report this page